How To Repair A Admiral Dryer Model# Ade7000ayw

We're sad, but our Q&A experts are temporarily unavailable.
Please check dorsum later if you lot still oasis't found the reply y'all demand.

2 questions answered past our experts.

Your search term must have 3 or more characters.

Keep searches simple. Use keywords, e.1000. "leaking", "pump", "cleaved" or "fit".

Distressing, we couldn't discover any existing answers that matched.Try using some unlike or simpler keywords, or submit your new question past using the "Inquire a Question" button above!

Solomon

November 28, 2022

Tin can I order replacement filter screen? And how much?

For model number LNC7764A71

Howdy Solomon, Give thanks you for contacting u.s.a.. I take researched the model yous have provided and accept found the part you are looking for is PartSelect Number PS11742807. Please enter the role number for current cost and availability. Promise this helps!

Was this helpful?

Thanks for voting!

Related Parts:

I'm replacing the dryer idlers assembly part number wp532366 don't know where to claw the tension bound that is attached to the shaft. It was unhooked when I went to replace the office. Can't figure out where information technology hooks to the frame?

For model number LNC7764A71

Hello Brian, give thanks you for writing. The bound hooks on the idler and into item # viii or part PS2048107 which is the housing. We accept a video for a similar appliance, that may be of some aid. If you demand assist placing an club, customer service is open 7 days a week. Please feel free to give the states a phone call. We look forrad to hearing from you.

Was this helpful?

Thanks for voting!

Related Parts:

lint filter broke

I pulled out the cleaved lint filter and put the new one back in, existent easy. I am then happy with the prompt commitment I got from PartsSelect.com. I ordered on a Monday and and information technology was delivered on a Wednesday

Parts Used:

• 

  Jane from Grand Forks, ND

• 

  Difficulty Level:

  Really Piece of cake

• 

  Total Repair Time:

  Less than 15 mins

477 of 485 people found this instruction helpful.

Was this education helpful to yous?

Give thanks you for voting!

Electric dryer would not heat - Thermal fuses - $25 prepare - I love DIY

ane. Unplug dryer from power outlet
2. Lift dryer meridian from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in textile to help lift.
three. Locate heating element - rear pinnacle behind drum
4. Unplug cherry wires to the loftier limit thermal fuse
five. Unplug ruby wires to the heating element
half-dozen. Unlug white wires to the high limit fuse
seven. Remove high limit thermal fuse
8. Remove heating element
ix. Remove high limit fuse
ten Clean heating box
Installation is reverse order but practice the following outset!
Clean lint trap - Remove front of dryer
ane. Unplug white door switch wires. inside front top right
ii. remove two screws securing the front end of dryer - inside front top left and top right. Front end of dryer is hinged at bottom
three. Clean all the lint you lot tin observe. If you lot have never cleaned out the lint, there might exist a lot and the cause of over heating (shorting fuse life). Add to your yearly things to exercise listing.
4. While your at it check the alignment of the plastic glides the drum sits on.
five. Also check the foam gasket between the fan housing and lint trap. Mine was off a fleck. Realigned with doubled sided tape.

Parts Used:

• 

  Ronald from Fredericksburg, VA

• 
• 

  Total Repair Time:

  30 - 60 mins

• 

  Tools:

  Nutdriver, Pliers, Screw drivers

207 of 226 people found this instruction helpful.

Was this instruction helpful to you?

Thanks for voting!

Dry stopped heating - still had good air flow

I was about to purchase a new dryer because of the historic period of my dryer and not wanting to hire someone to set up it. After a little web research, I saw several practice-information technology -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and information technology save me lots of $$:
(i) Disconnected ability
(2) Opened the top of the dryer
(3) Asunder wires to temperature sensor.
(iv) Used a i/2" socket wrench with extension and a drill to remove 2 screws belongings down the temperature sensor
(5) Removed 1 screw belongings down the heating element.
(6) Removed wires continued to heating element and pulled out old element.
(seven) Reassembled new element.
(8) Turned on empty dryer for 30 minutes to burn off smell from the new element.

Worked similar a charm!

Parts Used:

• 

  Brianna from Littleton, CO

• 

  Difficulty Level:

  Really Easy

• 

  Total Repair Time:

  Less than xv mins

• 

195 of 220 people establish this instruction helpful.

Was this instruction helpful to yous?

Thank you for voting!

How To Repair A Admiral Dryer Model# Ade7000ayw,

Source: https://www.partselect.com/Models/LNC7764A71/

Posted by: blackburnfooster.blogspot.com

Share this post